M1078A1 4x4 LMTV High Water Rescue Vehicle Painted to Match Township Fleet
Electronic - Caterpillar Turbo Diesel Engine, 7 Speed Allison Automatic Transmission
Tires 395/85R20 100% Tread - includes mounted spare
- Truck thoroughly checked to make sure all lights, signals, wipers and horn were in good operating condition.
- Engine fluids, belts, hoses and filters were replaced
- Axle, transmission, transfer case seals and fluids were checked and serviced
- Service and parking brake systems were checked and serviced including rebuilding or replacing components as required
- Extensively road tested
- Platform:
- Rear Loading Platform custom fabricated (air lines capped off & factory hitch
- removed) 36 inches Deep by 96 inches wide
- Rear corners of platform to be 45 degree chamfered
- Bar Grating decking (not punch plate)
- Fixed steps that go into the cargo bed, off the rear platform. (no hand rails or corner posts)
- Rope step ladders at left and right sides and 3 at center rear- from ground to platform (5 total)
- Anchor points/grab handles at each station at back of truck bed for personnel tether (1 left/1 right)
- Cab Interior:
- Cab headliner
- 2 dome lights connected to Door function with map light
- New floor mats and tower mats
- Recovered 2 seats black (center seat removed)
- Painted interior gloss black
- New front glass and gasket
- Removed toolbox and radio bag inside cab
- New door and window operators x 2
- USB Charging station
- Radio- AM/FM
- Light switch converted to Commercial
- Master battery disconnect switch - non-keyed - in Cab, easily accessible
- Relocated and Elevated exhaust to vertical Position
- Front push bumper with 2 “D” rings and 2 Rubber bumpers
- Heated Side Mirrors
- Installed supplied Antennas
- Cab entry step extensions and ladders
- Replaced front grille insert with heavy custom option
- Good Condition Computer scan reports provided for Cat Engine and Allison Automatic Transmission
- Bypassed CTIS system – capped off all fittings
- Backup Alarm and light with Display Screen inside cab
- Installed siren, siren controller, and 2 speakers
- Added Speaker location on front bumper
- Added antenna/disc locations on roof of cab
- Added Rear work lights
- Rear platform ladder painted same as rest of platform
- Rear cargo bed outer fold-downside panels (side tail gates)
- permanently affixed/screwed shut
- OEM Box behind driver seat was removed and was painted to match and installed
- Middle jump seat in the cab was removed
- Pre-wired for the Kussmaul charger and eject. Use 14-gauge wire.
- 12 volt leads for radio box, 1 positive and 1 negative. Home runs directed from batteries to Box behind driver seat. Used 8 Gauge wire.
- Added 60 Amp circuit breaker under the dash main electric panel and directed ground at same location (from truck frame to a stud) to be hidden from sight and have positive lug.
- Added direct ground from truck frame to a stud next to circuit breaker.
- Cut outside of box on cab side, edge with protective trim.
- Boat Motor mounted on headboard of bed.
- Painted and installed boat fuel tank bracket
- Boat Bag strap. 2 ratchet straps and “D” rings on floor and top of bed rail.
- Air tank bracket – Fabricated base bracket.
- Lighting: -
- All exterior Original Truck lighting upgraded to LED (Headlights, taillights, marker lights, front turn signals)
- Lighting elements, all switched inside of cab through Feniex Controller and work lights on toggle switches for front/side/rear separately
- Added Scene lighting at rear of cargo bed Corners
- Added 1 Reverse light, to make 2 total
- Furnished and Installed 6 each LED lights Feniex PN-Q-2222
- Furnished and Installed 2 each LED low profile warning light strip Feniex PN-QT-0420-ST (Red, Blue, White Lights)
- Furnished and Installed 16 total emergency lights around truck, Feniex QQM-8101
- Furnished and Installed 1 x 50" Forward Facing Brow Light, Heise
- Furnished and Installed 2 x 32" Side Facing Brow Lights, Heise
- Furnished and Installed 6 x 8" Side Facing Brown Lights, Side Body Under tucked, Heise
- Furnished and Installed LED Corner Compartment light for under cargo cover, Code 3
- Furnished and Installed 2 x Square LED Swivel work lights at rear, Code 3
- Cargo Bed:
- Rear cargo bed
- Rear side racks
- Toolbox seating with locking lids along 1 side only. Cushion on top. Approx 10 feet total.
- Removed seating drop down panel and insert 1x4 strip to reduce fall out risk
- Cargo Cover support system
- Custom rear canopy cover, Black, Clear plastic 3 side windows along each side. Rear panel extending down only approximately 6 inches below the top of rear bow.
- Added underneath storage trays to Cargo Bed, surface lined with textured bed liner to create closed storage
- Red LED strip lighting inside cargo bed at floor level
- D Rings welded inside head of cargo bed on floor – for assistance in loading bed
- Added storage tray/mount system for inflatable boat and motor.
- Rear work lights- made “L” bracket.
- Exterior:
- Exterior of truck, cleaned, prepared, primed and painted.
- Exterior Upper painted customer's fleet color
- Frame painted Black
- Wheels painted Black
- All walk on surfaces to be treated with Textured Rhino Style coating in Black